 |
Centering clamp with protective segments
Can be used from above.
Repeatability ± 0.025 mm
Concentricity ±0.025 mm
|
Order no.
|
D
min.
|
D
max.
|
A
min.
|
A
max.
|
H
|
P
[kN]
|
Weight
[g]
|
| 373670 | 14.5
|
18.5
|
8.6
|
9.8
|
14.5
|
3.5
|
18 |
| 373688 | 18.5
|
22.5
|
10.4
|
11.6
|
16.5
|
4.0
|
36
|
| 373696 |
22.5
|
26.5
|
13.0
|
14.2
|
19.8
|
4.5
|
61
|
| 373704 |
26.5
|
30.5
|
13.0
|
14.2 |
19.8
|
4.5
|
80
|
| 373712 | 30.5
|
38.5
|
11.9 |
14.2 |
23.2 |
4.5
|
114
|
| 373720 |
38.5
|
46.5
|
15.5
|
17.8 |
27.2
|
6.5
|
221
|
| 373738 |
46.5
|
54.5
|
15.7
|
18.0 |
27.2
|
6.5
|
305
|
| 373746 | 54.5
|
70.5
|
19.1
|
23.7
|
40.6
|
8.0
|
590
|
| 373753 | 70.5
|
86.5
|
23.7
|
28.3
|
46.1
|
10.0
|
1180
|
| 373761 | 86.5
|
102.5
|
25.7
|
30.2
|
51.0
|
12.5
|
1880
|
Dimensions:
Order
no.
|
B
|
B1
|
C
|
E f7
|
F
|
G
|
I ±0.1
|
K
|
L
|
M
|
M1
|
Q
|
QD
|
R
|
SW
|
T
|
|
373670 |
17.3
|
14.1
|
5.5
|
12
|
6
|
M6
|
4.5
|
2.0
|
2.3
|
M6
|
M3
|
3
|
4.0
|
12
|
5.5
|
2.5
|
|
373688 |
20.9
|
18.2
|
7.5
|
15
|
8
|
M8
|
5.5
|
2.5
|
2.3
|
M8
|
M4
|
3
|
4.0
|
14
|
7.0
|
3.5
|
|
373696 |
25.4
|
17.4
|
6.0
|
20
|
10
|
M10
|
7.0
|
3.0
|
2.3
|
M10
|
M5
|
3
|
4.0
|
15
|
8.0
|
3.5
|
|
373704 |
25.4
|
17.4
|
6.0
|
20
|
10
|
M10
|
7.0
|
3.0
|
2.3
|
M10
|
M5
|
3
|
4.0
|
15
|
8.0
|
3.5
|
|
373712 |
30.3
|
21.9
|
7.0
|
25
|
12
|
M12
|
9.0
|
4.0
|
4.6
|
M12
|
M6
|
3
|
8.0
|
20
|
10.0
|
3.5
|
|
373720 |
34.2
|
22.5
|
7.5
|
30
|
12
|
M12
|
11.0
|
4.0
|
4.6
|
M12
|
M6
|
6
|
8.0
|
20
|
10.0
|
4.5
|
|
373738 |
34.2
|
22.5
|
7.5
|
30
|
12
|
M12
|
11.0
|
4.0
|
4.6
|
M12
|
M6
|
6
|
8.0
|
20
|
10.0
|
6.5
|
|
373746 |
49.9
|
24.5
|
9.0
|
45
|
14
|
M14x1.5
|
15.0
|
5.0
|
9.3
|
M14x1.5
|
M8
|
6
|
16.0
|
32
|
13.0
|
6.5
|
|
373753 |
55.4
|
29.4
|
10.0
|
60
|
16
|
M16x1.5
|
17.0
|
5.0
|
9.3
|
M16x1.5
|
M8
|
6
|
16.0
|
20
|
13.0
|
6.5
|
|
373761 |
61.6
|
29.4
|
10.0
|
60
|
16
|
M16x1.5
|
25.0
|
5.0
|
9.3
|
M16x1.5
|
M10
|
6
|
16.0
|
25
|
16.0
|
6.5
|
Q=number of balls, QD=diameter of balls
Application:
For unmarred surfaces with central positioning and clamping in blind holes. Operation from below, automated or manual.
Note:
For deep installation, clearance D max. must be provided.
Installation tool: Hole K for retaining pin for determining the precise position of the segments. (supplied without installation tool)
Advantage:
- Low installation height
- Clamping in the zero point
- Pull-down effect
- Distortion-free clamping
|
|
|
STANDARD CLAMPING ELEMENTS
