 |
Centering clamp with ball
Can be used from above.
Repeatability ± 0.025 mm
Concentricity ±0.050 mm
|
Order no.
|
D
min.
|
D
max.
|
A
min.
|
A
max.
|
H
|
P
[kN]
|
Weight
[g]
|
| 373563 | 11.7
|
14.2
|
3.0
|
4.2
|
10.0
|
0.5
|
08 |
| 373571 |
14.5
|
18.5
|
8.6
|
9.8
|
14.5
|
3.5
|
18 |
| 373589 |
18.5
|
22.5
|
10.4
|
11.6
|
16.5
|
4.0
|
36 |
| 373597 |
22.5
|
26.5
|
13.0
|
14.2
|
19.8
|
4.5
|
61 |
| 373605 | 26.5
|
30.5
|
13.0
|
14.2
|
19.8
|
4.5
|
80 |
| 373613 | 30.5
|
38.5
|
11.9.
|
14.2
|
23.1
|
4.5
|
114 |
| 373621 |
38.5
|
46.5
|
15.5
|
17.8
|
27.2
|
6.5
|
221 |
| 373639 |
46.5
|
54.5
|
15.7
|
18.0
|
27.2
|
6.5
|
305 |
| 373647 |
54.5
|
70.5
|
19.1
|
23.7
|
40.6
|
8.0
|
590 |
| 373654 | 70.5
|
86.5
|
23.7
|
28.3
|
46.1
|
10.0
|
1180 |
| 373662 | 86.5
|
102.5
|
25.7
|
30.2
|
51.0
|
12.5
|
1880 |
Dimensions:
SW
Order
no.
|
B
|
B1
|
C
|
E f7
|
F
|
G
|
I ±0.1
|
K
|
L
|
M
|
M1
|
Q
|
QD
|
R
|
SW
|
T
|
|
373563 |
12.8 |
11.0 |
3.5
|
10
|
5
|
M5 |
3.5
|
1.5
|
1.4 |
M5 |
M3 |
3
|
2.5 |
10 |
5.5 |
2.0
|
|
373571 |
17.3 |
14.1 |
5.5 |
12 |
6
|
M6 |
4.5 |
2.0 |
2.3 |
M6 |
M3 |
3
|
4.0 |
12 |
5.5 |
2.5 |
|
373589 |
20.9 |
18.2 |
7.5 |
15 |
8
|
M8 |
5.5 |
2.5 |
2.3 |
M8 |
M4 |
3 |
4.0 | 14 |
7.0 |
3.5 |
|
373597 |
25.4 |
17.4 |
6.0 |
20 |
10 |
M10 |
7.0 |
3.0 |
2.3 |
M10 |
M5 |
3
|
4.0 |
15 |
8.0 |
3.5 |
|
373605 |
25.4 |
17.4 |
6.0 |
20 |
10 |
M10 |
7.0 |
3.0 |
2.3 |
M10 |
M5 |
3 | 4.0 |
15 |
8.0 |
3.5 |
|
373613 |
30.3 |
21.9 |
7.0 |
25 |
12 |
M12 |
9.0 |
4.0 |
4.6 |
M12 |
M6 |
3
|
8.0 |
20 |
10.0 |
3.5 |
|
373621 |
34.2 |
22.5 |
7.5 |
30 |
12 |
M12 |
11.0 |
4.0 |
4.6 |
M12 |
M6 |
6
|
8.0 |
20 |
10.0 |
4.5 |
|
373639 |
34.2 |
22.5 |
7.5 |
30 |
12 |
M12 |
11.0 |
4.0 |
4.6 |
M12 |
M6 |
6
|
8.0 |
20 |
10.0 |
6.5 |
|
373647 |
49.9 |
24.5 |
9.0 |
45 |
14 |
M14x1.5 |
15.0 |
5.0 |
9.3 |
M14x1.5 | M8 |
6
|
16.0 |
32 |
13.0 |
6.5 |
|
373654 |
55.4 |
29.4 |
10.0 |
60 |
16 |
M16x1.5 |
17.0 |
5.0 |
9.3 |
M16x1.5 |
M8 |
6
|
16.0 |
20 |
13.0 |
6.5 |
|
373662 |
61.6 |
29.4 |
10.0 |
60 |
16 |
M16x1.5 |
25.0 |
5.0 |
9.3 |
M16x1.5 |
M10 |
6
|
16.0 |
25 |
16.0 |
6.5 |
Q=number of balls, QD=diameter of balls
Application:
For central positioning and clamping in blind holes where slight ball impressions are acceptable. Operation from below, automated or manual.
Note:
For deep installation, clearance D max. must be provided.
Installation tool: Hole K for retaining pin for determining the precise position of the balls. (supplied without installation tool)
Advantage:
- Low installation height
- Clamping in the zero point
- Pull-down effect
- Distortion-free clamping
|
|
|
STANDARD CLAMPING ELEMENTS
